Lindby Linbar Highway Bar

Yes, that is one of the models that you can choose from the Select Your Vehicle section before adding to your cart.

This standard Linbar would not work. However, there is one offered that will. You would just need to search our site for Lindby Linbar Highway Bar for Bikes with Forward Controls. That would be the bar you would want to use for that 1996 FXDWG with forward pegs.

Yes, this Linbar will work with floorboards on that 1996 FLSTF Fat Boy.

It would likely work if attached low near the mount point to the frame. It was secured wide outside it will likely cause issues and bend when pulled tightly.

So long as it's the stock floorboards that you have on your 2006 FLSTF Softail Fat Boy, then yes these Lindby Highway bars to fit your machine!

Yes, if you were to choose the 2016 Harley Davidson FLSTN Softail Deluxe Lindby Linbar highway bar from our fit guide, you'd receive the correct Softail Deluxe highway bars to fit your machine. We have them in either, chrome or black for your bike.

Unfortunately no, the Linbar from Lindby is only available in chrome to fit the Yamaha Raider. If you would, have a look at the Lindby Multibar Highway Bar for the Yamaha Raider. That particular unit is indeed available in a black powder coated finish. About the only difference between the Yamaha Raider Linbar and the Lindby Multibar for the Yamaha Raider is that the latter has bonded rubber footrests. If you like to put your feet up while you cruise, the added grip makes a big difference in comfort!

Unfortunately no, Lindby's bars won't work with Cobra floorboards. The same holds true for pretty much every set of highway bars out there as they're only tested on machines with the stock foot controls. That said, check out the Cobra Fatty Freeway Bars for the VTX1800R as they're specifically engineered to work with Cobra floorboards. So far as we're aware, Cobra highway bars are the only highway bars that will certainly work with Cobra floorboards.

If you're fitting this Linbar to a 2005 Kingpin, yes it includes the long threaded bolt you're referring to. In addition, the spacers, washers &etc. are also included in the box. In fact, the 2005 Kingpin Linbar parts list is as follows: 7/16"-14 x 12-1/2 in. threaded rod (qty. 1) Upper mount spacers (qty. 2) 3/8" Flat washers (qty. 2) 1/2" Flat washers (qty. 2) 7/16"-14 x 2.75" Allen bolts (qty. 2) 7/16"-14 Nyloc nuts (qty. 4)

Yes, we do have a Lindby Linbar to fit the 2012 Harley FLTRX Road Glide. Just choose your machine from our fit guide and we'll send the proper kit straight to your door. Plus, you'll find a simple set of instructions and all required installation hardware for fitting the FLTRX highway bar to your bike. No special tools or extra parts required!

In the case of the 2009 Yamaha V-Star 950 Tourer Lindby Linbar Highway Bar, it weights about 16 lbs. It's made entirely of 1-1/4" outside diameter .120 thick steel. While Lindby doesn't provide us with exact specs for width of the bar, they're usually between 31-36 inches. Smaller cruisers such as the 950 Tourer will have the smaller width closer to 31". Only the larger Harley Davidson models will have a 36" width bar.

So far as I know, it was the 2003 model year XL1200C that came with a forward controls option straight from the factory, but not the 2004 and up models. That said, if the forward controls you're referring to don't extend past the front frame downtubes, then the Lindby Highway bar we have on offer will indeed fit your machine.

So long as it's the stock floorboards that you have on your 2016 Softail Fat Boy Low, then yes these Lindby Highway bars to fit your machine!

Yes, this Linbar will fit the 2016 Kawasaki Vulcan 900 Classic LT. There are no additional clamps or hardware required in order to fit it to the VN900 - everything you need is included in the box. The upper portion of the Linbar for the Vulcan Classic 900 is attached on the same place as the horn while the lower portions are bolted to the frame on the front portion of the floorboards. That is to say, the Linbar is attached to the Kawasaki's front floorboard mounting bolts. Lindby includes the appropriate, longer hardware to facilitate this installation.

In the case of the VTX1300S (and all other VTX1300 models), there are no U-bolts used to fasten the Lindby highway bars for the VTX1300. These highway bars attached to the top radiator mounts (6mm bolts) and include bolts and spacers to accommodate this arrangement. The lower portion is attached to the forward OEM footpeg mounts.

Lindby's highway bars to fit the Victory Kingpin Tour don't bolt directly to or through the bike's frame, at least not the upper part. Rather, the kit comes with a set of U-clamps that attach to the upper portion of the front downtubes, just below the steering head. The lower portion of the highway bars are attached using the included hardware on the front floorboard mounts. In this way, you get a solid, workmanlike attachment that doesn't require any permanent modifications to your Victory. You'll find the installation rather straightforward and will take less than half-an-hour even taking the most leisurely pace to get the work done.

Generally speaking, forward controls and highway bars are mutually exclusive. That is to say, you can have one or the other, but not both. In the case of the 2014 Yamaha Stryker, these highway bars will indeed fit your machine, but you'll have to remove the Scootmod 3" forward control extensions that you have since they'll get in the way of the highway bars.

Yes, we have the Lindy Highway Bar will fit a 2007 Harley-Davidson FLHX Street Glide. Simply choose your bike from the Select Your Ride box that's to the right of the main image and we'll get the correct highway bars to fit your bike on the way, guaranteed!

Yes indeed. All required mounting hardware is included with all Lindy highway bars. Everything you need for a clean installation is included in the box.